IP Subnet Calculator
Calculate subnet masks, CIDR notation, usable host counts, broadcast addresses and full network ranges from any IPv4 address.
Open tool →Free, engineering-grade calculators for infrastructure professionals. 12 Live 37 Total 12 Categories
Results
Calculate subnet masks, CIDR notation, usable host counts, broadcast addresses and full network ranges from any IPv4 address.
Open tool →Plan and document VLAN segmentation, trunk assignments and inter-VLAN routing for structured network designs.
Open tool →Calculate IPv6 subnets, prefix lengths and address ranges for dual-stack environments.
Coming soonCalculate exact patch cord lengths for rack-to-rack and device connections with metric/imperial support and slack allowance.
Open tool →Estimate total cable quantities including pulls, drops and waste factors for horizontal and vertical distribution.
Open tool →Calculate conduit fill percentages for mixed cable bundles per NEC and EN standards.
Coming soonVisually plan equipment placement in 19" and 23" racks with U-space tracking, weight distribution and cable management zones.
Coming soonCalculate Power Usage Effectiveness and compare against ASHRAE and Green Grid benchmarks for data centre efficiency tracking.
Coming soonInteractive reference guide for TIA-942 Tier I–IV requirements covering power, cooling and structural criteria.
Coming soonCalculate total rack power draw, current per phase and PDU sizing from individual equipment entries with real-time totals.
Open tool →Size a UPS system by VA/kVA requirement and calculate expected battery runtime under varying load percentages.
Open tool →Plan N, N+1, 2N and 2(N+1) power path redundancy for critical IT loads.
Coming soonEstimate technical-room and server-room cooling demand in kW, BTU/h and tons, including IT load, UPS losses, lighting, people, safety margin, airflow and cooling-failure temperature-rise guidance.
Open tool →Convert between BTU/hr, tons of refrigeration, kW and kCal/hr for cooling capacity planning across international standards.
Open tool →Size precision air conditioning units based on IT load, sensible heat ratio and redundancy requirements.
Open tool →Verify if server inlet conditions meet ASHRAE A1–A4 / X1–X2 equipment environment classes.
Open tool →Select correct AWG or mm² wire size based on load current, voltage, run length and insulation rating to NEC/IEC standards.
Coming soonCalculate voltage drop percentage for single-phase and three-phase circuits over given cable lengths and loads.
Open tool →Calculate total circuit load, diversity factors and breaker sizing for multiple connected loads.
Open tool →Calculate annual electricity costs for IT equipment based on power draw, utilisation and tariff rates.
Coming soonBuild a 5-year total cost of ownership model including CapEx, OpEx, power, cooling and staffing.
Coming soonEstimate CO₂ emissions from IT infrastructure based on power consumption and regional grid emission factors.
Coming soonBuild structured project scope documents with effort estimation, material lists and timeline milestones.
Coming soonBuild itemised cost proposals for installation projects including labour, materials and margin calculation.
Coming soonEstimate capital expenditure for infrastructure refresh or new builds across structured cabling, rack, power and cooling.
Coming soonSize a solar PV array for off-grid or hybrid use based on load profile, location irradiance and battery capacity.
Coming soonSize a diesel or gas generator for standby or prime power based on connected load, starting current and duty cycle.
Coming soonDesign a battery bank for off-grid or UPS applications including cell count, string voltage and autonomy calculation.
Coming soonCalculate total home electrical load, select consumer unit size and check against supply capacity.
Coming soonPlan home network topology: router placement, AP coverage, switch locations and cable runs room by room.
Coming soonSelect the right consumer or small office UPS size for your PC, NAS or home lab equipment.
Coming soonEstimate incident energy and arc flash boundary for LV/MV panels based on system impedance and protective device clearing time.
Coming soonSelect the correct PPE category for electrical work tasks based on NFPA 70E and IEC 61482 standards.
Coming soonVerify earthing conductor sizing and ground resistance requirements to IEC 60364 and NEC Article 250.
Coming soonCalculate total network bandwidth for IP CCTV systems based on camera count, resolution, codec and frame rate.
Coming soonEstimate NVR/DVR storage requirements based on camera count, bitrate, retention period and motion recording settings.
Coming soonCalculate camera field of view, detection distance and identification distance for different lens focal lengths.
Coming soonNo calculators found.
Available Calculators
Live tools ready to use now.
All Categories
Subnet calculators, VLAN planning, IP addressing and network topology tools for structured LAN/WAN design.
Cable length calculators, patch cord planners, conduit fill tools and TIA-568 / ISO 11801 reference guides for professional cabling installations.
Rack unit planners, PUE calculators and TIA-942 reference tools for data centre design and capacity management.
Rack power density calculators, UPS sizing, battery runtime and redundancy planning tools for critical power systems.
CRAC/CRAH sizing, BTU/kW conversion, ASHRAE envelope checks and airflow management tools for data centre thermal design.
Wire gauge selectors, circuit load calculators, conduit fill tools and voltage drop estimators for LV electrical installation design.
Energy consumption and electricity cost calculators, TCO analysis and carbon footprint estimators for infrastructure operation.
Project scoping, resource estimators, proposal calculators and timeline tools for IT infrastructure project planning and tendering.
Solar PV sizing, generator selection, battery bank calculators and hybrid system planning tools for sustainable and resilient power.
Home network design, consumer UPS sizing, small office electrical load calculators and residential structured cabling tools.
Arc flash incident energy calculators, PPE selection tools, earthing/grounding checks and electrical safety reference guides.
CCTV camera coverage planners, IP video bandwidth calculators, NVR storage estimators and access control system design tools.